×

Discussion Board

Results 1 to 7 of 7
  1. #1
    Registered User
    Join Date
    Jan 2007
    Posts
    4

    Unhappy Problems with E61 and IP-PBX system... Please Help

    I am looking for some help in regards to setting up the E61 to work off of my router, which is connected to my PBX. It is a IP-PBX config and I am attempting to set up the Nokia as an exstention. However there is one key problem that I can not seam to work around while the other wired SIP phones work fine on the system. (Note: friends SIP only WiFi phone is working perfect)

    While the Nokia is showing that the registration has failed, the PBX is showing it as a live and active exstention. When wired phone dials Nokia exstention PBX send the appropriate request to the Nokia with no avail. The problem seams to be coming from ICMP and a port 3478 which appears to be assosiated with the STUN, and timing out issues of the Nokia (note: No firewall on system) Below is the captured packet data that I have added if anyone could help me make a little more out of this data.

    No. Time Source Destination Protocol Info
    1 0.000000 192.168.Nokia 192.168.Router TCP 36092 > 3478 [SYN] Seq=0 Len=0 MSS=1460 TSV=240193072 TSER=0 WS=0

    2 0.000013 192.168.Router 192.168.Nokia TCP 3478 > 36092 [RST, ACK] Seq=0 Ack=1 Win=0 Len=0

    3 3.025200 192.168.Nokia 192.168.Router TCP 36092 > 3478 [SYN] Seq=0 Len=0 MSS=1460 TSV=243205947 TSER=0 WS=0

    4 3.025427 192.168.Router 192.168.Nokia TCP 3478 > 36092 [RST, ACK] Seq=0 Ack=1 Win=0 Len=0

    5 3.061877 192.168.Nokia 192.168.Router STUN Message: Binding Request

    6 3.062182 192.168.Router 192.168.Nokia ICMP Destination unreachable (Port unreachable)
    User Datagram Protocol, Src Port: 5060 (5060), Dst Port: 3478 (3478)
    Source port: 5060 (5060)
    Destination port: 3478 (3478)
    Length: 28
    Checksum: 0x282d [correct]
    Simple Traversal of UDP Through NAT


    (note: all ports are 5060 for both src and dst after above port issue)
    7 3.107896 192.168.Nokia 192.168.Router SIP Request: REGISTER sip:192.168.1.200;transport=UDP

    8 3.129120 192.168.Router 192.168.Nokia SIP Status: 407 Proxy Authentication Required (0 bindings)

    9 3.306115 192.168.Nokia 192.168.Router SIP Request: REGISTER sip:192.168.1.200;transport=UDP

    10 3.343778 192.168.Router 192.168.Nokia SIP Status: 200 OK (0 bindings)

    Nokia appears to go to sleep after this portion and nolonger responds to request from system.

    I may be a little over my head on this but any help anyone can offer would be great.

  2. #2
    Registered User
    Join Date
    May 2006
    Location
    Bay Area, CA, USA
    Posts
    13

    Re: Problems with E61 and IP-PBX system... Please Help

    Make sure you have upgraded your E61's firmware. Without it, there is no STUN support.

  3. #3
    Registered User
    Join Date
    Jan 2007
    Posts
    4

    Re: Problems with E61 and IP-PBX system... Please Help

    It is upgraded to V 3.0633.09.04 which I was informed is the most up to date but correct me if I am wrong? thanks

  4. #4
    Registered User
    Join Date
    Jan 2007
    Posts
    4

    Re: Problems with E61 and IP-PBX system... Please Help

    Does anyone know if there is a copy of the standard sip settings out there that has just the stun dissabled or will that option be avalible via the UI in a possible future update. This currently appears to be the only road block I am running into right now. Dont know if that is the actual fix, but worth a try. Thanks

  5. #5
    Nokia Developer Expert
    Join Date
    Dec 2006
    Location
    Mountain View, CA
    Posts
    197

    Re: Problems with E61 and IP-PBX system... Please Help

    The STUN settings needs to be provisioned (OMA DM OTA SMS or by SISX file) for STUN support to work. Do I asumme correctly that the settings have been inserted manually?

  6. #6
    Registered User
    Join Date
    Jan 2007
    Posts
    4

    Re: Problems with E61 and IP-PBX system... Please Help

    nly, saddly right now I am only working via the UI, and no VoIP provider avalible to send me an sms as this is a basic phone line with a IP-PBX built on to it. From reading over the forum to get better educated, it appears that I might have to wait until Nokia release a feature which will allow one to config their own setting for the STUN/NAT trasversal. As my above data capture indicates that it is the port 3478 that is the main issue.

  7. #7
    Registered User
    Join Date
    Jul 2007
    Posts
    2

    Re: Problems with E61 and IP-PBX system... Please Help

    Quote Originally Posted by ChrisS
    I am looking for some help in regards to setting up the E61 to work off of my router, which is connected to my PBX. It is a IP-PBX config and I am attempting to set up the Nokia as an exstention. However there is one key problem that I can not seam to work around while the other wired SIP phones work fine on the system. (Note: friends SIP only WiFi phone is working perfect)

    While the Nokia is showing that the registration has failed, the PBX is showing it as a live and active exstention. When wired phone dials Nokia exstention PBX send the appropriate request to the Nokia with no avail. The problem seams to be coming from ICMP and a port 3478 which appears to be assosiated with the STUN, and timing out issues of the Nokia (note: No firewall on system) Below is the captured packet data that I have added if anyone could help me make a little more out of this data.

    No. Time Source Destination Protocol Info
    1 0.000000 192.168.Nokia 192.168.Router TCP 36092 > 3478 [SYN] Seq=0 Len=0 MSS=1460 TSV=240193072 TSER=0 WS=0

    2 0.000013 192.168.Router 192.168.Nokia TCP 3478 > 36092 [RST, ACK] Seq=0 Ack=1 Win=0 Len=0

    3 3.025200 192.168.Nokia 192.168.Router TCP 36092 > 3478 [SYN] Seq=0 Len=0 MSS=1460 TSV=243205947 TSER=0 WS=0

    4 3.025427 192.168.Router 192.168.Nokia TCP 3478 > 36092 [RST, ACK] Seq=0 Ack=1 Win=0 Len=0

    5 3.061877 192.168.Nokia 192.168.Router STUN Message: Binding Request

    6 3.062182 192.168.Router 192.168.Nokia ICMP Destination unreachable (Port unreachable)
    User Datagram Protocol, Src Port: 5060 (5060), Dst Port: 3478 (3478)
    Source port: 5060 (5060)
    Destination port: 3478 (3478)
    Length: 28
    Checksum: 0x282d [correct]
    Simple Traversal of UDP Through NAT


    (note: all ports are 5060 for both src and dst after above port issue)
    7 3.107896 192.168.Nokia 192.168.Router SIP Request: REGISTER sip:192.168.1.200;transport=UDP

    8 3.129120 192.168.Router 192.168.Nokia SIP Status: 407 Proxy Authentication Required (0 bindings)

    9 3.306115 192.168.Nokia 192.168.Router SIP Request: REGISTER sip:192.168.1.200;transport=UDP

    10 3.343778 192.168.Router 192.168.Nokia SIP Status: 200 OK (0 bindings)

    Nokia appears to go to sleep after this portion and nolonger responds to request from system.

    I may be a little over my head on this but any help anyone can offer would be great.
    Hey Chris,
    I am running my Nokia E62 registered through MediaNet(accesspoint)(not wifi) registering to my friend trixbox/Asterisk VoIP PBX.

    I have included the standards SIP settings that I'm using on my E62 to get it to register to my IP-PBX.

    "Nokia E62 SIP Settings / Asterisk Settings

    SIP Config.

    Profile Name: Asterisk

    Service Profile: IETF

    Default Access Point: Media Net (or your providers access point)

    Public User Name: sip:XXX@trixdomain.com (XXX = the extension you are assigned on the trixbox)@(domain or public IP of the trixbox)
    Use Compression: No

    Registration: Always on

    Use Security: No

    PROXY SERVER

    Proxy server address: sip:trixdomain.com (domain or public IP of the trixbox)
    Realm: asterisk (make sure to use a lower-case a)

    Username: XXX (your extension setup on the trix)

    Password: **** (your extension password)

    Allow loose routing: Yes

    Transport type: UDP
    Port: 5060

    Registrar server

    Registrar serv. addr.: sip:trixdomain.com (domain or public IP of the trixbox)

    Realm: None

    User name: None

    Password: None

    Transport type: UDP

    Port: 5060"

    I also have alot of random information/setitngs for Trixbox PBX's on this page I made, http://blog.spanosg.com/. Hope this was helpful.

    What PBX are you using?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •