Revision as of 08:50, 12 May 2007 by vasant21 (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

AT Commands

From Nokia Developer Wiki
Jump to: navigation, search



Call Control

ATA - Answer Command

ATD - Dial Command

ATH - Hang Up Call

ATL - Monitor Speaker Loudness

ATM - Monitor Speaker Mode

ATO - Go On-Line

ATP - Set Pulse Dial as Default

ATT - Set Tone Dial as Default

AT+CSTA - Select Type of Address

AT+CRC - Cellular Result Codes

Data Card Control Commands

ATI - Identification

ATS - Select an S-register

ATZ - Recall Stored Profile

AT&F - Restore Factory Settings

AT&V - View Active Configuration

AT&W - Store Parameters in Given Profile

AT&Y - Select Set as s Powerup Option

AT+CLCK - Facility Lock Command

AT+COLP - Connected Line Identification Presentation

AT+GCAP - Request Complete Capabilities List

AT+GMI - Request Manufacturer Identification

AT+GMM - Request Model Identification

AT+GMR - Request Revision Identification

AT+GSN - Request Product Serial Number Identification

Phone Control Commands

AT+CBC - Battery Charge

AT+CGMI - Request Manufacturer Identification

AT+CGMM - Request Model Identification

AT+CGMR - Request Revision Identification

AT+CGSN - Request Product Serial Number Identification

AT+CMEE - Report Mobile Equipment Error

AT+CPAS - Phone Activity Status

AT+CPBF - Find Phone Book Entries

AT+CPBR - Read Phone Book Entry

AT+CPBS - Select Phone Book Memory Storage

AT+CPBW - Write Phone Book Entry

AT+CSCS - Select TE Character Set

AT+CSQ - Signal Quality

Computer Data Card Interface Commands

ATE - Command Echo

ATQ - Result Code Suppression

ATV - Define Response Format

ATX - Response Range Selection

AT&C - Define DCD Usage

AT&D - Define DTR Usage

AT&K - Select Flow Control

AT&Q - Define Communications Mode Option

AT&S - Define DSR Option

AT+ICF - DTE-DCE Character Framing

AT+IFC - DTE-DCE Local Flow Control

AT+IPR - Fixed DTE Rate


AT+CLIP - Calling Line Identification Presentation

AT+CR - Service Reporting Control

AT+DR - Data Compression Reporting

AT+ILRR - DTE-DCE Local Rate Reporting

Network Communication Parameter Commands

ATB - Communications Standard Option

AT+CBST - Select Bearer Service Type

AT+CEER - Extended Error Report

AT+CRLP - Radio Link Protocol

AT+DS - Data Compression

Miscellaneous Commands

A/ - Re-Execute Command Line

AT? - Command Help

AT*C - Start SMS Interpreter

AT*T - Enter SMS Block Mode Protocol

AT*V - Activate V.25bis Mode

AT*NOKIATEST - Test Command

AT+CESP - Enter SMS Block Mode Protocol

SMS Commands SMS Text Mode

AT+CSMS - Select Message Service

AT+CPMS - Preferred Message Storage

AT+CMGF - Message Format

AT+CSCA - Service Centre Address

AT+CSMP - Set Text Mode Parameters

AT+CSDH - Show Text Mode Parameters

AT+CSCB - Select Cell Broadcast Message Types

AT+CSAS - Save Settings

AT+CRES - Restore Settings

AT+CNMI - New Message Indications to TE

AT+CMGL - List Messages

AT+CMGR - Read Message

AT+CMGS - Send Message

AT+CMSS - Send Message from Storage

AT+CMGW - Write Message to Memory

AT+CMGD - Delete Message


AT+CMGL - List Messages

AT+CMGR - Read Message

AT+CMGS - Send Message

AT+CMGW - Write Message to Memory

2040 page views in the last 30 days.

Was this page helpful?

Your feedback about this content is important. Let us know what you think.


Thank you!

We appreciate your feedback.